ABSTRACT

 In our society today reading and writing has taken its roll as a way of measuring human knowledge.  Knowledge could only be obtain successively by the use of books for research but unfortunately because of hard time, books have because very expensive. This has called for preservation of books already purchased, whether in the public library school or in the house hold so that it can use for future reference.  These could only be done by stocking books systematically in a bookshelf where by it can be free from rat, insects and other thing that could destroy books. Our own contribution towards this development is the design and manufacture of a bookshelf that will be economically cheap and at the same time meet up its demands.Bookshelf could be made with metals or wood and they could be attached against the wall or they could be made standing on the floor.  Our bookshelf shall be of the metal type standing on the floor. 


 TABLE OF CONTENT Title page    -        -        -        -        -        -        -        -        -                  Approval page -   -        -        -        -        -        -        -        -        Declaration -        -        -        -        -        -        -        -        -                  Table of content - -        -        -        -        -        -        -        -        Dedication  -        -        -        -        -        -        -        -        -        Acknowledgement         -        -        -        -        -        -        -        Abstract -   -        -        -        -        -        -        -        -        -        CHAPTER ONE 1.1            Introduction         -        -        -        -        -        -        -        -        1.2            Description of Material Used  -        -        -        -        -        1.3            Purpose of the Study     -        -        -        -        -        -        1.4            Scope and Objectives of the Study   -        -        -        -        CHAPTER TWO 2.1     Literature Review          -        -        -        -        -        -        2.2     Design analysis    -        -        -        -        -        -        -        2.3     Capacity of bookshelf    -        -        -        -        -        -        CHAPTER THREE 3.1            Material selection -        -        -        -        -        -        -        3.2            Tools/Equipment -        -        -        -        -        -        -        3.3            Construction        -        -        -        -        -        --       -        3.4            Sequences of operation  -        -        -        -        -        -        CHAPTER FOUR4.1            Cost analysis        -        -        -        -        -        -        -        CHAPTER FIVE5.1            Conclusion -        -        -        -        -        -        -        -        5.2            Guidelines on usage       -        -        -        -        -        -        5.3            Recommendation -        -        -        -        -        -        -        REFERENCE APPENDIX 
 CHAPTER ONE 1.1            INTRODUCTION A bookshelf is a device with partitions use for the purpose of save-guarding books and files in offices, libraries and at homes. A bookshelf can be wooden, metal or glass.  They could also be design in such a way that they could be dismountable or undismountable.  In our project, we decided to design and fabricate on undismountable metallic bookshelf. Among all the bookshelfs, the undismountable metallic bookshelf has the longest lift span because of its rigidity, quantity of material and it ability to with stand heavy loads.  In other words, the constant loosening and coupling of the component parts which lead to the weakness of the bolt and nut, thus subject the shelf to vibration. Our project being the undismountable bookshelf was fabricated with variety of material.  The types of materials involved are mild steel square pipes (25mm x 25mm) mild steel sheet metal, etc.  in this, the square pipes were used in the fabrication of the frame work   The essence of creating steel fame work with pipes is for it to withstand the stress that will be develop due to the weight of the material and loads or each partition. In fabrication, the frame was first erected before covering with the mild steel sheet.  The mass and volume of the book to be contained by each partition were considered before they were erected, so certain experiment were carried out which will be discusses in detail in this report. 1.2     DESCRIPTION OF THE METAL BOOK SHELF The metal bookshelf is made up of the following parts and components. (i)                The frame work (ii)             The side (iii)           The top (iv)           The stand (v)             The partitions          THE FRAME The frame is the skeleton of the whole shelf, it is made of 25mm square pipe and 25mm (1) by 50mm (2) rectangle pipe.  The frame was first erected together by mean of welding before the sheet was covered at the back, side, top and the partitions. The frame was design to withstand the stress that will be develop on it due to the weight of sheet metal and load on each partition. THE SIDE The side is made up of a mild steel of 0.8mm thick with height 1700mm and width 700mm.  It was welded to the frame (at an angle 900).  THE TOP OR PLANE The top is made up of a mild steel sheet of thickness 0.8mm and 1700mm height by 600mm width and it is also welded diagonally to the frame. (I.e. at angle 900) THE STAND The stand were made from a rectangle pipe and a square pipe, that is, the two back stand were made from square pipe while the two front stands were made from the square pipe.  This stand were extended from the frame work to enable stronger gripe, avoid bending, breaking and also to avoid slip. THE PARTRITIONS The partitions were design to be able to contain large number of books. They are measured 360mm by height, 1222mm by length and 470mm by breath.  The material used for the partitions was mild steel plate of 1.2mm thick was welded to the frame work of the partitions. The volume of the partition = l x b x h = 1222 x 470 x 360 = 206762400mm   AREA OF PARTITION = 2(lb + bh + lh) = 2(1222 x 470) + (470 x 360) + (1222 x 360) =2(574340)+ (169200) + (439920) =2(1183460) = 2366920mm.1.3     PURPOSE OF THE PROJECT The purpose of this project is to design and construct a metallic bookshelf capable of containing different standard, size books. The design should be able to complete favourably with other accepted standard. 1.4     SCOPE AND LIMITATION OF THE STUDY The shelf is of four (4) partitions constructed with metal which is the best material for the construction of engineering device of this type and in each partition distance the distance =410mm which bring it to the total of 16inches.